Screw driver slipped
Screw driver slipped
I was putting a slk800 onto my asus a7n8x deluxe, and the screw dirver slipped. Now its not booting. I'm not getting any beeps, the fans and power lights are coming on. I took a close look at it and it looks like a couple of the traces got scratched. Is it possible to fix something like this?
<marquee><span style="width: 100%; Filter: Glow(Color=#3333FF, Strength=2)">I was here</span></marquee>
That really sux. 
I've had that happen a few times but have always been lucky that nothing was damaged. Since then though, I always try several flathead screwdrivers in the clip and choose one that fits it the best before any install.
Perhaps some kind of tiny conductive wire may help. Maybe solder them on or even tape to see if it helps. Never tried that though. And as you, I can't see things that small.
I've had that happen a few times but have always been lucky that nothing was damaged. Since then though, I always try several flathead screwdrivers in the clip and choose one that fits it the best before any install.
Perhaps some kind of tiny conductive wire may help. Maybe solder them on or even tape to see if it helps. Never tried that though. And as you, I can't see things that small.
[align=center]<img src="http://www.statgfx.com/statgfx/folding/?&username=blade&border=0,0,64&custom=21,138,255&label=79,79,255&header=149,202,255&stats=0,255,255&bgcolor=0,0,181&trans=no&template=fah_original&.jpg" alt="www.Statgfx.com" />
<img src="http://www.pcabusers.org/funnies/monkey2.gif">
<i><small>"Too much monkee business"</i></small>[/align]
<img src="http://www.pcabusers.org/funnies/monkey2.gif">
<i><small>"Too much monkee business"</i></small>[/align]
-
eGoCeNTRoNiX
- Posts: 7362
- Joined: Wed Oct 23, 2002 12:51 pm
- Location: HELL
That sux..
I've actually started using a "device" to help protect the mobo if I do slip. I took one of those Saran Wrap cutting boards (the thin ones) and cut a piece out to fit between the socket and the capacitors (be there any) so that if I did/do slip I don't mess anything up. 
eGo
eGoPM before Email People!!
Heat Under eGoCeNTRoNiX
Who Farted? BEANIE!!!
!Welcome to the United States of the Offended!
Heat Under eGoCeNTRoNiX
Who Farted? BEANIE!!!
!Welcome to the United States of the Offended!
good idead ego, I imagine a dense piece of hobby foam cut thin would work good too, We can all slipped, i have yet to kill one though
[align=center]<img src="http://www.statgfx.com/statgfx/folding/?&username=Billygoat(pcabusers)&border=0,255,0&label=255,0,0&header=0,0,255&stats=0,0,0&bgcolor=255,255,0&trans=no&template=fah_original&.jpg" alt="PCA Folding Rules!" />[/align]
I got a new board today and guess what? Booted to bios, I set up the ram cpu and that fun stuff. Saved and exited then no boot again. cleared the bios and set it up again, then no boot again, cleared the bios again. Then booted to bios yet again, set up only the cpu and clock. Wouldn't boot.
tried it at 100 and it booted to windows, at 133 it wouldn't boot at all. Pulled the cpu out and cleaned it to check it out real good, It had no visible damage. Put it back in, set the cpu to 166, and it wouldn't boot. set it at 133 and it booted. I went through this several times till it finally started to boot at 166. strangest thing I have seen.
I'm going to try another cpu in the old board later to see if its bad.
tried it at 100 and it booted to windows, at 133 it wouldn't boot at all. Pulled the cpu out and cleaned it to check it out real good, It had no visible damage. Put it back in, set the cpu to 166, and it wouldn't boot. set it at 133 and it booted. I went through this several times till it finally started to boot at 166. strangest thing I have seen.
I'm going to try another cpu in the old board later to see if its bad.
<marquee><span style="width: 100%; Filter: Glow(Color=#3333FF, Strength=2)">I was here</span></marquee>