Fan speed

NascarFool · Post by **NascarFool** » Mon Aug 19, 2002 8:14 pm

I just pulled the loud HeatPipe HSF and replaced it with an SLK-800 and a Thermal Take SmartFan (80mm). My temps ar higher now, I used AS3 on it. (XP2200+ @ 11x178x1.75v) Should I wire the fan to run on high speed all the time ? My comp is absolutely silent with it on low speed.

HeatPipe Temps:
42ºC Idle - Side cover off
52ºC Load

SLK-800 Temps
46ºC Idle - side cover off
50ºC Idle - Side cover on
No temp for full load yet

dadx2mj · Post by **dadx2mj** » Mon Aug 19, 2002 8:21 pm

Guess it comes down to if the commuter is stable and personal preference. Myself I will gladly put up with a little noise for the peace of mind a cool CPU gives me.

NascarFool · Post by **NascarFool** » Mon Aug 19, 2002 8:27 pm

I didn't realize how loud the CoolerMaster was with the 7K fan on it. It's ony a few degrees and I already like the silence.

blade · Post by **blade** » Mon Aug 19, 2002 10:11 pm

Are you sure the SLK800 is pushed mostly to the rear? What happened to me is I had it too far towards the front and without realizing it, the heatisnk slightly overhung the front plastic. Since it wasn't fully contacting the cpu temps were high, once I noticed that and moved the heatsink back temps dropped about 14 degrees.

That may not be the problem but thought I'd be sure.

Also for fun, try the same fan on both heatsinks and see the diff.

Peace and quiet is most good.

NascarFool · Post by **NascarFool** » Mon Aug 19, 2002 10:37 pm

Looks like it is all the way where it needs to be. I don't think I'll take it off to try the 80mm on the HeatPipe.

I did drop the voltage down to 1.70v and the temp came down to 42ºC.

System Specs:
400w PS
Epox 8K3A+ Rev. 1.2
XP2200+ @ 11x178x1.70v (1.97GHz, not bad for air cooling)
Third party Samsung 512megPC2700 @ 2.7v
Radeon 8500 retail @ 285.8/285.8
SB Live X-gamer non- 5.1
2x40gig WD ATA100/7200rpm in RAID0
30gig WD ATA100/5400rpm storage on IDE2 (slave)
Pioneer 16x Slot load DVD on IDE1 (master)
Plextor 40x12x40x CD-RW on IDE2 (master)
Lite-On 40x CD-ROM on IDE1 (slave)
NetGear FA311 NIC
Directron Hydraulic mid tower (80mm front intake, 80mm side intake and 60mm @ 5v back exhaust)

SLK-800 installed - no fan.

Rounded cables installed and fan installed. Like my homemade hard drive bracket ?

blade · Post by **blade** » Mon Aug 19, 2002 10:53 pm

I always install the fan first, then attach the heatsink to the mobo. And the chin bone connected to the..

Just worries me moving that heavy sink around, may damage the cpu.

Actually I meant trying the heatpipe fan on the slk800. But I know, too much trouble. But I like doing all that.

Like my homemade hard drive bracket ?

Hey, it works!

PreDatoR · Post by **PreDatoR** » Mon Aug 19, 2002 11:05 pm

I recognize a couple of those rounded cables

case looks nice and clean like mine on the inside...

NascarFool · Post by **NascarFool** » Mon Aug 19, 2002 11:18 pm

One of those cables could have been a 1/2" longer for the DVD drive at the top. It almost didn't reach. The wife is gonna kill me if I decide to get a window kit.

I couldn't use the Thermal Take grill on the fan, so I used it on my case to replace the gold wire grill. I need to clean the side a little.

PreDatoR · Post by **PreDatoR** » Mon Aug 19, 2002 11:21 pm

LOL yeah my 10" Floppy cable could be half inch longer too i should have ordered the 12" one instead. I got it stretched to its limit

Ya clean that side off looks like you've been fondling it