post your amd xp overclocks!!

Thermite Paste · Post by **Thermite Paste** » Mon Aug 23, 2004 7:05 pm

post your amd athlon xp overclocks! dont forget to post what cooling you have!

ill start with mine - AMD athlon xp 2800 @ 2.225 ghz with 180 fsb and 12.5 multiplier. once i get a new mobo ill go higher. my cooling is a stock heatsink.

Pugsley · Post by **Pugsley** » Mon Aug 23, 2004 7:41 pm

2500 @ 3200 speeds... 190 FSB and voltage slightly hot. Using a sp97 and a quiet slow fan and under full load with room temp at 82.6 its running at 116.4

123cool · Post by **123cool** » Tue Aug 31, 2004 2:28 pm

2100+(1.73Ghz) @ 2200+(1.9Ghz). cooling = AK795 (stock 3000+ fan+heatsink) FSB = 144 with +3v.

impuresoul2k3 · Post by **impuresoul2k3** » Tue Aug 31, 2004 3:16 pm

2200+ speeds are 1.8ghz, not 1.9ghz

123cool · Post by **123cool** » Wed Sep 01, 2004 10:43 am

2200+ speeds are 1.8ghz, not 1.9ghz

i know. the properties in windows xp reported a 1.9Ghz speed but the proccessor as a 2200+.

p.s

anyone know how to mod a AK795 heatsink so that it can hold a 80mm fan?

ShibasScotch · Post by **ShibasScotch** » Wed Sep 01, 2004 1:06 pm

Barton 2400M @ 200x11.5 >> Reports as a 3200+, but the clock is higher than a stock 3200

impuresoul2k3 · Post by **impuresoul2k3** » Wed Sep 01, 2004 3:28 pm

Originally posted by 123cool
i know. the properties in windows xp reported a 1.9Ghz speed but the proccessor as a 2200+.

Oh, ok

blade · Post by **blade** » Sat Sep 04, 2004 12:23 am

xp2500+ @ 3200+, sp97 with 92mm tornado. Fan controlled by a fan controller, naturally. It can go higher, 12x206. But, fan has to be too loud. Runs at 11.5x200 just fine, but for summer I'll keep it at 11x200. I prefer peace and quiet.

Thermite Paste · Post by **Thermite Paste** » Sat Sep 04, 2004 12:44 am

mmm..... unlocked xp 2500+.....

blade · Post by **blade** » Sat Sep 04, 2004 1:02 am

Yep. Too bad they locked newer ones. But from what I've seen, most will still do 11x200, 11x190 at the very least. Still not shabby at all.

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Sat Sep 04, 2004 9:06 am

Originally posted by ShibasScotch
Barton 2400M @ 200x11.5 >> Reports as a 3200+, but the clock is higher than a stock 3200

Ditto..

As blade mentioned they're locking the new ones. I have one of each. A Locked and Unlocked. My Unlocked is on an Epox 8RDA+ (This is my favorite board I have had 0 problems with it since I got it) running at 11.5x200 w/SLK-900A Runs at 49* C Under full load. Only because I keep the fan turned down.

My Locked is running on a Chaintech 7JNL1? Or somethin' like that..

heh.. It's running at 11x205 w/no problems at all. It's got an SLK-800 and runs a little warmer than this one, couple of degrees me thinks. But in the near future I'll be swapping the processors in the boards to run the unlocked in a watercooling rig and really see what it can do.

eGo

Key Keeper · Post by **Key Keeper** » Mon Nov 08, 2004 10:25 pm

2600+ barton running at 2.228 says wcpuclk. 194x11.5, ZALMAN copper/aluminum running at full speed, temp runs 43c, also a locked processor. I left my voltage set to auto in my bios, 1.61 says my soyo hardware monitor software.

TruckStuff · Post by **TruckStuff** » Tue Nov 09, 2004 6:32 am

Running a 2000+ at 12.5 x 166Mhz (2.1Ghz). XP reports this as a 2600+ even thouch its closer to a 3000+. Just running the retail HSF. I know it could go higher, but my RAM starts to flake out at higher FSBs. Maybe someday I'll put some faster RAM in their and buy a better HSF, but doesn't Doc say you need a 30% increase in CPU speed to "feel" a difference in the system? I doubt I'll be able to squeeze 2.7Ghz out of a 1.6Ghz stock CPU.

BillyGoat · Post by **BillyGoat** » Thu Nov 18, 2004 7:12 pm

mobile 2400+ @ 2.50= 500fsb on water- have toasted this chip up to 2.7, but i dont like to send as much voltage as that takes- never hits over 36 degrees

wvjohn · Post by **wvjohn** » Thu Nov 18, 2004 7:42 pm

nice one BG