8rda+ Let's Burn!

blade · Post by **blade** » Mon Sep 08, 2003 9:44 pm

Try 1.7. After that if no go you can try 1.75 or even 1.8. good luck

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Mon Sep 08, 2003 9:48 pm

Ok.. I'll try that.. BTW I've also got Corsair XMS PC3200 in here now, not that 2700 I was using before.. eGO

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Mon Sep 08, 2003 10:24 pm

Maybe.. Hmmmmm.. Ok Guys. It seems like it was only locking up as soon as it went to start folding w/the GUI... So, should I switch to the cmd line version and see what happens? I've got high hopes for this chip.. it's at 11.5x189 I'm gonna try the over version with some of the other settings and see what happens.. eGo

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Mon Sep 08, 2003 11:44 pm

Nothing New.. eGo

Absolut Talent · Post by **Absolut Talent** » Tue Sep 09, 2003 12:29 am

Originally posted by Chris305
Don't overclock that much. My friend was overclocking and his computer got on fire.

ROFL

:laugh :laugh

that is the funniest thing I have read in awhile

chak22 · Post by **chak22** » Tue Sep 09, 2003 10:27 pm

EGO.... Whats the word? Any new updates to report ?

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Tue Sep 09, 2003 10:33 pm

Well, I had a little "fiasco" last night and thought i'd fried the board.. lol.. Turned out the CMOS jumper was just in the wrong spot. So, right now it's at 11.5x186 2.04ghz I'm just gonna take it slow like you are and see where it leads me. Temps reading at 37*C I don't think that's too shabby for a Zalman 6000cu lol.. I'll update it every few days.. This PC hauls ass as it is.. Folded one of those 2500 WU's in about 20 hours.. he he.. Watch out peoples! I've got 3 boxes above 1Ghz now, and two that aren't 830mhz and 900mhz.. HE HE HE!!! eGo

chak22 · Post by **chak22** » Tue Sep 09, 2003 10:58 pm

That darn CMOS jumper ... I've done that more than a few times myself and then I catch it and say to myself...."You Idiot"!! Sounds like you are Cruising along nicely so far ,I bumped up to up to 11.5 X 198 today so far so good on the Barton , try to hit the 200 tomorrow . temps are looking good so far for you ,What voltage are you running thru the processor? I also noticed that I knocked off nearly 2 minutes off each folding unit going from 195 fsb to 198 fsb must be I hit a sweet spot , well keep us all informed .............

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Tue Sep 09, 2003 11:09 pm

Default on the VCore. I'm very pleased with the combo. I too was calling myself an idiot.. lol..

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Sun Sep 14, 2003 1:07 pm

Ok Guys.. Been stepping it up a little day by day.. Right now i'm at 11x191 or 2101mhz.. Not bad at all.. Maintaining temps of 35.5* Idle and up to 39* Load depending on room temp. Though it's normally 70* in here. Just wait to see my temps this winter since I don't use heaters.. he he he.. I'll post again in a few days.. eGo

buddhazen · Post by **buddhazen** » Tue Sep 16, 2003 10:09 am

is there a way i can check the stepping on my chip without removing the hs/f
i have a xp1700 chip on a kt400 chip that does 2 ghz on air at default voltage with pc2700 ram
any help appreciated

eGoCeNTRoNiX · Post by **eGoCeNTRoNiX** » Tue Sep 16, 2003 10:22 am

You can't check the steppings without removing the HSF AFAIK.. I know that it would be very difficult for you to get a TBred A to those speeds.. GL eGO

buddhazen · Post by **buddhazen** » Tue Sep 16, 2003 1:13 pm

yeah i built an extra pc right after i bought my main one
never bothered about steppings because the chip was only 42 bucks off newegg
guess i got lucky then

PCA Forums

8rda+ Let's Burn!

WoW..

The Wall?

NM

Gettin' up there..

Went To..

Updates..

It's Probaly a Tbred B